Podzemná komplexná galéria trubiek Prefabrikované komponenty Podrobný výrobný proces

Oct 19, 2018

Zanechajte správu

Podzemné komplexné rúry pre galériu prefabrikované komponenty výrobný proces podrobne


Najprv nastavenia miesta konania


Prefabrikované miesto

1. Stránka je vybraná podľa aktuálnej situácie projektu. Táto lokalita zaviedla uzavreté riadenie na nastavenie dovozu a vývozu a prístupová cesta pre výstavbu je vyhradená v oblasti plánovania lokalít a na základe dovozu a vývozu sa podľa predpisov vzťahujú rôzne znaky.

2. Usporiadanie miesta prefabrikácie musí byť striktne v súlade s požiadavkami štandardnej továrne, musí spĺňať požiadavky systému BOZP a HSE a musí byť zriadené rôzne zariadenia na ochranu životného prostredia. Musí byť plne vybavený tak, aby spĺňal požiadavky na bezpečnú a civilizovanú výrobu, vypúšťanie odpadových vôd a likvidáciu odpadu. Prísne v súlade s príslušnými ustanoveniami miestnych orgánov.

3. Vyčistite prefabrikované miesto, vyrovnávanie, vibrovanie a zhutňovanie, položte 20cm silnú cementom stabilizovanú makadamovú základňu, vyhladzujte a vibrujte a zhutňujte. Hlavná cesta elektrárne na cementom stabilizovanú makadamovú základňu vyleje 15 cm silný komerčný betón C20. , montážna plocha, prefabrikácia, výrobná oblasť, integrovaná dýzová galéria prírodná pamiatková rezervácia rozliatie 10cmC20 komerčný betón. V polohe montáže koľajových žeriavov je hĺbka výkopu 60 cm a betón sa naleje a dráha sa položí. Tiež tieto tri veci:

(1) Miesto musí byť vyčistené a vyrovnané, vrátane montovaných miest, spájanie stavebných pásov a existujúcich dopravných ciest a priechodov v prefabrikovaných lokalitách.

(2) V prefabrikovanej lokalite by sa mali vyčistiť kamene, buriny, stromy, konštrukcie atď., Ktoré ovplyvňujú prechod alebo stavebné práce stavebných strojov, priekopa a hrebeň by mali byť vyrovnané a nízko položené plochy s nahromadenou vodou by mali byť odčerpané a naplnené, ak je to potrebné, zmenené. Vyplňte, plne zaručte rovinnosť povrchu a nosnosť a tlakovú kapacitu.

(3) Vyčistenie a vyrovnávanie miest pred začatím výroby sa vykoná s cieľom zachrániť nadobúdanie pôdy alebo využívanie pôdy, žiadne prekážky v premávke, žiadne škody na budovách, zariadeniach, pamiatkach atď., Aby sa zabránilo znečisteniu životného prostredia a erózii pôdy.


4. Prefabrikácia spracovacej a inštalačnej plochy oceľovej tyče, integrovaná priestor na výrobu paropriepustných priestorov na výrobu rúr, integrovaná kanalizačná šachta prírodnej ochrany, integrovaná úložná oblasť potrubia a ďalšie funkčné oblasti. Kancelárska plocha a obytná plocha sú nastavené podľa aktuálnej situácie a prefabrikovaný vstup a výstup z poľa je zriadený ako strážna miestnosť. Po druhé, výrobný proces


Vývojový diagram výrobného procesu

1. Výstužné stavebné materiály vstupujúce na stavbu, inšpekcia odberu vzoriek, spracovanie ocele, viazanie oceľovej tyče, inštalácia.

(1) Kontrola prístupu k výstuži a. Rebar je oceľová oceľ HPB300 valcovaná za tepla a oceľová tyč HRB400 valcovaná za tepla. Štandardná pevnosť oceľovej tyče spĺňa požiadavky bodu 4.2.2 normy GB50010-2010. Rebrovaná oceľová tyč je v súlade s oceľou pre železobetón: Časť II: Oceľové tyče s valcovaním za tepla valcované za tepla (GB1499.2-2007); ľahké oceľové tyče spĺňajú požiadavky ocele na železobetón: Časť I: oceľové tyče s valcovaním za tepla valcované za tepla (GB1499.1-2008). Oceľová doska je vyrobená z ocele Q235-B, oceľová oceľ HPB300 je zváraná elektródou typu E43 a oceľová oceľ HRB400 je zváraná elektrodou typu E55. b. Pred vstupom ocele na miesto skontrolujte rozmanitosť, triedu, špecifikáciu, množstvo a zoznam materiálov v prísnom súlade s požiadavkami, či je certifikát kvality výrobku, správa o kontrole z výroby a správa o opätovnej kontrole úplné a platné. Skúška mechanických vlastností musí byť v súlade s príslušnými normami. c. Pred vstupom ocele na pole a pred použitím skontrolujte kvalitu vzhľadu oceľovej tyče, či už je rovná, bez poškodenia, nezaradenie na povrchu, trhliny, praskliny, olejové škvrny, zrná alebo vločka stará hrdza, rovnomerné zafarbenie , pozri priemer oceľovej tyče Splniť požiadavky, aby sa neovplyvnila pevnosť ocele a kotviaci výkon. Oceľové dosky, zváracie tyče atď. Sa skontrolujú s kontrolnými prvkami z oceľovej tyče pred vstupom na miesto.

(2) Skladovanie oceľových tyčí a. Oceľové tyče vstupujúce na miesto sú uložené v skladovacej oblasti oceľovej tyče podľa odrody, špecifikácie a triedy. Materiály uchovávajú materiálni zamestnanci a opatrovníci. Ocelová tyč musí byť pokrytá podložkou, aby sa zabránilo hrdzi. b. Skontrolujte, či je oceľová tyč vybavená certifikátom o továrni a správou o inšpekcii a správou o kontrole. Skontrolujte kvalitu vzhľadu a priemerný objem. Oceľový stĺp musí byť komplexne skontrolovaný pre jeho index kvality. Podľa inšpekcie šarží je priemer a hmotnostná odchýlka rovnaké ako tá istá továreň, rovnaké číslo pece, rovnaká špecifikácia, rovnaký výrobný postup a 60-tonová oceľová tyč, ktorá vstupuje na rovnakú stavenisku súčasne inšpekčná dávka menej ako 60 ton. Rovnako ako testovaná dávka vykonajte svedectvo odberu vzoriek. Odber vzoriek z oceľových tyčí vykoná technik vykonávajúci dozor. Dve oceľové tyče sa odoberajú dvoma skúšobnými kusmi v ťahu, každá s dĺžkou približne 450 mm, a dvoma skúšobnými kusmi za studena s dĺžkou približne 350 mm, umiestnenými v testovacej skrinke a potom pod dohľadom na tesnenie alebo monitorovanie v skúšobnej miestnosti. Ak je výsledok správy o opätovnom preskúmaní nekvalifikovaný, vykoná sa dvojnásobný výber vzorky a opätovne sa testuje. Výsledky správy o opätovnom preskúmaní musia byť kvalifikované a inžinier odborného dozoru podpíše schválenie a dávka oceľových tyčí sa môže použiť pri spracovaní. Skladovanie a skladovanie iných materiálov sa vykonáva pomocou izolácie proti vlhkosti.

(3) Spracovanie výstuže pred spracovaním Pred spracovaním sa podľa konštrukčných špecifikácií a dĺžky a množstva v kombinácii s rôznymi spôsobmi spracovania stanoví dĺžka každej výstuže výpočtom, aby sa zaistila presnosť. Počas spracovania skontrolujte, či v tabuľke s vyprázdňovaním nejaká chyba alebo opomenutie. Skontrolujte tabuľku materiálov pre každý typ oceľovej tyče. Po týchto dvoch kontrolách stlačte tabuľku materiálov, čím uvoľníte skutočnú vzorku. Po vykonaní skúšobnej výroby je možné ju spracovať v dávkach. Dobré oceľové tyče by mali byť uložené úhľadne a usporiadané. Povrch oceľovej tyče musí byť čistý a mastnota, špina a hrdza musia byť pred použitím vyčistené. Oceľové tyče sú narovnávané a mechanicky vyrovnané. Oceľové tyče po rovnaní nesmú mať miestne ohýbanie, mŕtve ohyby alebo malé vlny. Rezanie oceľového tyče by malo byť založené na čísle, priemere, dĺžke a množstve oceľovej tyče. Dĺžka a dĺžka oceľovej tyče by sa mali zlomiť a najprv by sa mal roztrhnúť krátky materiál a krátka oceľová hlava by sa mala čo najviac znížiť a skrátiť, aby sa ušetrila oceľ a znížila strata. Keď je oceľová tyč ohnutá, určuje bod ohybu a určuje uhol ohybu na základe odrazovej pevnosti každej oceľovej tyče. Pred formálnym ohýbaním sa oceľové tyče, ktoré boli ohnuté vo veľkých množstvách, podrobia skúšobnému ohnutiu a príslušné technické údaje sa určia pred ohýbaním šarží. Po ohnutí oceľovej tyče oblúk tvorí oblúk. Po ohýbaní veľkosť nie je väčšia ako rozmery. Je potrebné zvážiť hodnotu nastavenia ohybu. Priemer ohybu D ohýbanej oceľovej tyče a ohyb strednej časti nie je menší ako 5-násobok priemeru oceľovej tyče. Dĺžka oceľovej tyče by sa mala posudzovať komplexne podľa veľkosti komponentu, hrúbky ochrannej vrstvy a nastavenej hodnoty ohýbania oceľovej tyče. Prípustná odchýlka spracovania oceľovej tyče nesmie presiahnuť špecifikáciu. Pri oceľových tyčiach s nedostatočným hotovým materiálom sa metóda zvárania tupým spojom používa na zachytenie dĺžky nohy a potom ohyb. Zvárač na tupo musí byť vycvičený špeciálnym zváracím procesom a odobratý na kontrolu. Po vytvorení rôznych oceľových tyčí prípustná odchýlka nesmie prekročiť špecifikáciu: celková dĺžka silových rebier musí byť ± 10 mm; odchýlka dĺžky každej časti strmene je ± 5 mm; odchýlka ohnutých rebier musí byť ± 20 mm od člena, veľký objem betónu je ± 30 mm; odchýlka oceľového rohu je 3 mm; kruhové rebro 6 až 12 mm je vyrobené do strmeňa a dĺžka koncového háku je 75 až 105 mm podľa priemeru hlavného rebra. Stanoví sa špecifický výpočet pred vyčistením, spracované oceľové tyče sa klasifikujú a skladujú a vytvoreným oceľovým tyčkam sa zabráni deformácii počas skladovania a prepravy.


Oceľové debnenie z pleteného skeletu (vystuženej ocele)

Ťažkosti: Obtiažnosť vytvárania hlavných rebier obdĺžnikového horného potrubia je vonkajšie rebro hlavné rebro. Každý krúžok pozostáva zo štyroch oceľových tyčí s dvomi oblúkmi, z ktorých každá tvorí pravouhlý rebrový prsteň s hornou rúrkou Polomer oblúka je príliš malý, zakrivený segment oblúka je krátky a presnosť je vysoká. , Riešenie: Pred ohýbaním oceľových tyčí označte ich na priesečníku každého oblúka. Potom sa oblúk R90 ohýba ohýbaním v troch valcoch a priamkový segment nie je ohnutý. Po úplnom ohnutí oblúka sa umiestni na štandardnú hlavnú kontrolu. Po splnení požiadaviek sa značka polohy pohyblivého kolesa umiestni na operačnej plošine ohýbacieho stroja pre ďalšiu rýchlu výrobu. Stroj na ohýbanie tromi valcami musí mať funkciu jog a reverz. (4) Zváranie oceľových tyčí Tvarovaná oceľová tyč sa umiestni na oceľový nástroj na zváranie podľa konštrukčných výkresov na zváranie. Kvalita zvárania je dôležitou súčasťou zabezpečenia celkovej pevnosti oceľovej tyče. V továrni na spracovanie oceľových tyčí sa oceľové tyče hlavne očistia obojstranným tupým zváraním na okraji, aby sa pred privarením očistili rohové omietky a hrdza na čelnej strane, olejové škvrny a oxidový film a kovový lesk bol vystavený brúseniu a nedochádza k žiadnemu oxidačnému javu. Súčasne by mala byť koncová plocha oceľovej tyče sploštená, aby sa uľahčila dobrá kombinácia. Upevnenia na obidvoch stranách by mali byť zarovnané, aby sa zabezpečilo, že obe oceľové tyče sú na tej istej osi a miestna vôľa dvoch oceľových tyčí nie je väčšia ako 3 mm. Tlak použitý počas zvárania by mal byť rovnomerný a silný a teplota by sa mala regulovať pri 30-40 MPa v závislosti od priemeru oceľovej tyče, aby sa dosiahla dobrá priľnavosť medzi týmito dvoma oceľovými tyčami. Ak sú oceľové tyče rôznych priemerov zvárané na tupo, odchýlka nesmie prekročiť 7 mm. Zváranie na tupo a bodové zváranie sú prísne v súlade s predpismi a pracovníci zvárania sú certifikovaní. Po dokončení zvárania sa kĺb zmení z bielej na čiernu, čím sa uvoľní svorka a oceľová tyč sa vyberie hladko, aby sa zabránilo ohnutiu. Po ukončení zvárania oceľových tyčí sa vykoná kontrola vzhľadu zvarových spojov v čase a spoje, ktoré zlyhajú vizuálnu kontrolu, sa znova zvárajú. Všetci operátori na zváranie musia zabezpečiť, aby všetky typy zváracích strojov boli v dobrom prevádzkovom stave, zvládli hlavné výkony a parametre rôznych zváracích strojov v čase a aby vybrali najlepšie parametre pre skutočnú prevádzku v závislosti od podmienok základného kovu a počasia, kvality zvárania. , (5) Pred špecifikáciou, veľkosťou, tvarom, množstvom, polohovacím náradím atď. By sa mali revidované oceľové klietky znovu kalibrovať a komplexná kontrola by sa mala vykonať podľa konštrukčných výkresov a zoznamu zložiek. Návrh, zoznam zložiek a fyzický objekt je možné zosúladiť. Bezpečnosť. Pred inštaláciou systému je výstuž umiestnená na pracovnej plošine podľa konštrukčných údajov. Zároveň sa podľa umiestnenia stanovuje nastavenie stojacej výstuže, aby sa zabezpečilo, že oceľové tyče po inštalácii spĺňajú požiadavky. V procese bezpečnosti sa oceľové tyče vyrábajú najmä drôtenou väzbou a bodovým zváraním. Otvory sú vyrobené z 20 ~ 22 # drôtu. Spôsob väzby a viazania je v súlade so špecifikáciami a predpismi. Bodové zváranie sa používa hlavne na tvarovanie oceľových tyčí a stojanov. Pripevnenie, bodové zváranie by malo byť pevné, body by mali byť rovnomerne rozložené a silové rebrá by nemali byť vážne poškodené. Upevňovací kĺb oceľovej tyče musí spĺňať tieto požiadavky: a. Koniec dĺžky pása nesmie byť menší ako 10-násobok priemeru oceľovej tyče v ohybe oceľovej tyče a spoj nesmie byť umiestnený pri maximálnom ohybovom momente komponentu. b. V napínacom pásme sa koniec oceľového spojenia ocele triedy I zhotoví do háku. V tej istej časti musí byť prierez spojenia napínacieho pásma menší ako 50% celkovej plochy spoja prijímajúceho silu a spojovací článok nesmie byť väčší ako 50%. Najviac 25%, v rovnakom čase nesmú uviaznuté spoje presiahnuť 50% v kompresnej zóne. c. Zosilnené spoje, spojené s drôtom v strede a na oboch koncoch. d. Spojovacie polohy stlačených rebier sú vzájomne odstupňované. Dĺžka pása napnutých oceľových vystužených spojov by mala spĺňať konštrukčné požiadavky. Zvárané oceľové spoje a mechanické spojenia by mali byť umiestnené pri minimálnom ohybovom momente a rozložené. e. Ak je priemer namáhanej oceľovej tyče ≥25 mm, neodporúča sa používať nevábo- vaný uchytený spoj. f. Hrúbka betónovej ochrannej vrstvy namáhanej oceľovej tyče musí spĺňať konštrukčné požiadavky. Aby sa zabezpečila správna poloha oceľovej tyče, je to zviazané a inštalované podľa konštrukčných požiadaviek. g. Pri procese viazania výstužnej klietky je na štyroch stranách spoja vopred prikryté jedno potrubie PVP, Φ14mm, dĺžka PVC rúrky sa určuje podľa hrúbky steny ústia spoja a predbežne vloženého PVC potrubie sa používa ako kontrolný otvor a vstrekovací otvor. Zvedacie otvory sú inštalované vo výške 500 mm nad a pod stredovou osou ľavej a pravej strany integrovanej galérie. Dva oceľové rúry Φ125 * 10mm * 220mm sú na oceľový rám pripevnené a oceľová doska Φ140 * 4 sa používa na utesnenie. Oceľová rúrka Φ125 * 10mm * 180mm je inštalovaná pred zdvíhaním. Φ110mm * Železný kolík s hrúbkou 350 mm sa používa ako uško na uchytenie rúrok, ktoré zodpovedá zdvíhacej konštrukcii integrovanej trubice. Dielektrické práce sú skryté projekty. Pred nalievaním betónu by mali byť ocelové tyče a vložené časti kontrolované a akceptované a skryté technické záznamy by sa mali robiť. Po tom, čo inžinieri dohľadu na mieste súhlasia, môže byť vykonaný ďalší proces.


Zostava oceľovej formy

Najúčinnejšou metódou pri montážnom procese by malo byť: prvá podpora vnútornej formy, prstencové spojovacie rebrá z ocele by mali byť najprv privarené a potom umiestnené do spodnej formy a oceľové krúžky spojujúce rebrá objímky by mali byť po oceliach zvárané rám sa vloží do formy a oceľové tyče sa zvárajú. Po vložení kostry do formy sa zvárajú injektážne otvory, injektážny otvor a vopred zabudovaná oceľová doska. Po zváraní je vonkajšia forma zostavená. Aby sa zabránilo tomu, že pozícia zdvíhacieho otvoru je nepresná, je zdvíhací otvor upevnený na vonkajšej forme a vonkajšia forma je zostavená a potom je zváracia objímka pripravená. Zakrytý oceľový krúžok. (6) Zosilnená ochranná vrstva Ochranná vrstva betónu je zhotovená z betónového bloku, hrúbka sa rovná hrúbke navrhovanej ochrannej vrstvy, veľkosť bloku je 3 cm x 3 cm, počet vložiek je viac ako C25 maltová pevnosť a vytvrdzovanie sa počas výroby zvyšuje, aby sa dosiahla konštrukčná pevnosť. Môže sa použiť 85% vyššie uvedeného. Pri použití vo vertikálnej štruktúre môže byť v bloku zabalená 20 viazacia čiara a blok je viazaný na oceľovú tyč pomocou drôtu. Spodná vrstva spodnej dosky a vrstvy vystuženej steny sú umiestnené na jeden štvorcový meter na meter štvorcový a sú usporiadané švestky. Rozstupy podložiek by mali byť správne šifrované. Rozpoznanie blokov a ich tesné pripevnenie na oceľové tyče namáhané namiesto toho, aby boli umiestnené na nenosených šľachách, by malo byť pevné, aby sa zabránilo posunutiu a skĺznutiu počas procesu liatia; či sú bloky pred nalievaním betónu úplne skontrolované Chýba alebo je poškodený. 2. Betónové liatie (1) Betónový materiál Preprava betónu sa prepravuje na prefabrikované miesto betonovým tankerom a čerpá do skladu betónovým čerpadlom. Pokles betónu sa spravidla pohybuje medzi 140 a 180 mm (špecifická hodnota závisí od teploty dňa). 4 betónové vibračné tyče s vibračným polomerom 20-25 cm, takže vzdialenosť medzi každou tyčou je 40 cm. Každá hĺbka tyče je pod 5 cm pod predchádzajúcim vibračným povrchom a doba vibrácie na tyči je 2-3 minúty. (2) Konštrukcia zmiešavacieho pomeru a skúška a. Konštrukcia zmiešavacieho pomeru Na splnenie požiadaviek pevnosti konštrukcie betónu, odolnosti proti mrazu, nepriepustnosti, rýchlosti rozptyľovania piesku a stavebnej spracovateľnosti, test optimalizácie betónového mixu zároveň spĺňa požiadavky stavebného pomeru vody a cementu a poklesu, a je preskúmaná a schválená inžinierom. Pomer miešania betónu by mal zabezpečiť, aby získaný betón mohol spĺňať špecifické podmienky liatia a spotreba vody v pomere betónu je čo najmenšia. b. Testovací pomer betónového mixu test betónového pomeru, vrátane testu pomeru betónovej zmesi a betónového testu výkonnosti rôznych stupňov pevnosti, testu pomeru miešania 14d pred rôznymi testovanými zložkami zmiešavacích pomerov a zmiešavania, tvarovania a údržby atď. Plán skúšok zmiešavacích pomerov sa oznamuje inžinierovi. c. Kontrola pomeru konštrukčného mixu Podľa testu zmiešavacieho pomeru a zoznamu dávok schváleného inžinierom je pomer miešania betónu riadený a celková spotreba vody je upravená podľa obsahu vody v agregáte. Prepad betónu je určený povahou konštrukčnej časti, rýchlosťou vystuženia, metódou betónovej prepravy a odlievania a klimatickými podmienkami a čo najviac využíva malý prepad. Prepad betónu spĺňa požiadavky SL677-2014. (3) Skúška na odber vzoriek betónu Počas procesu nalievania betónu musí dodávateľ vykonať betónový odber vzoriek na mieste vypúšťania a odlievania podľa ustanovení SL352-2006 a pokynov dozorného orgánu a predložiť dozornému orgánu nasledujúce materiály : a. A osvedčenie o kvalite integrovanej galérie potrubia; b. Zloženie, zmiešavanie a rozmery skúšobného kusu; c. Opis prípravy a údržby skúšobného kusu; d. Výsledky testov a opis; e. Betón rôznych vekových kategórií Skúšobné údaje ako objemová hustota, pevnosť v tlaku, pevnosť v ťahu, medza pevnosti v ťahu, modul pružnosti, pomer Poissona, pokles a počiatočné nastavenie a konečný čas nastavenia. (4) Nalievanie betónu a. Kombinovaný pomer komerčného betónu by mal spĺňať požiadavky DL / T5330-2005 "Špecifikácia konštrukčného riešenia pre pomer miešania betónu" a používať prostriedok na redukciu cementu a vody s relatívne skorým počiatočným nastavením času a skorým zvýšením pevnosti po konečnom nastavení. Rôzne prísady, ako je činidlo na odvádzanie vzduchu a činidlo s rýchlou silou, by mali zvážiť dlhú vzdialenosť betónovej dopravy, zvýšiť skorú pevnosť betónu, skrátiť dobu odlúpnutia, skrátiť dobu výstavby a zvlášť vyriešiť pomalý nárast pevnosti betónu počas zimnej výstavby , Problém s betónovým prepadom na mieste má byť kontrolovaný na úrovni 140-180 mm. b. Po tom, ako boli inštalované formy a oceľové tyče a kvalifikované technikmi pre kontrolu a dohľad nad kvalitou a potvrdené, možno nalievať integrovanú galériu potrubia. Výška otvoru je 2 m alebo viac nad zemou a pokles je 2 m alebo menej. Mäkká strunová hlaveň je nastavená v ústí, aby sa zabezpečilo, že betón má výšku pádu menej ako 2 m. c. Betónový betónový tunelový betón musí prijať metódu symetrického odlievania, aby zvážila, že výška okraja by nemala presiahnuť 40 cm a metóda kontinuálneho liatia by nemala byť prerušovaná. d. Betón sa naleje v vrstvách, v určitom smere a s určitou hrúbkou. Betón je horizontálne vrstvený a hrúbka vrstvy je 30-40 cm. e. Vibrovanie používa zásuvnú vibračnú tyč, pohybová vzdialenosť nepresahuje 1,5 násobok polomeru pôsobenia vibračnej tyče a udržiava vzdialenosť 5 až 10 cm od bočnej formy. Vložte spodnú vrstvu betónu 5 až 10 cm pri vibrácii a pomaly navrhujte vibračnú tyč po každej vibrácii. Zabráňte vibrácii debnenia, oceľových tyčí atď. Počas vibrácií; pre každú vibračnú časť musí byť oscilovaná až do zhutnenia betónu, to znamená, že betón sa zastaví, bez bublín a povrch je plochý a bahnitý. Počas procesu odlievania by každý typ práce mal byť usporiadaný na kontrolu zmien oceľových tyčí, konzol a šablón a situácia by sa mala riešiť v čase. 3, údržbu a odstraňovanie zubov


Box prechodové prefabrikované

(1) Po naliatí betónu, po prvotnom nastavení betónu, je integrovaná rúrková rúra parou pri vysokej teplote. V pare sa prijíma prispôsobený parný poklop a integrovaná forma trubice je pokrytá pariacim krytom a spodná časť parného krytu je utesnená, aby sa zabránilo vyprázdňovaniu pary počas procesu pary. Napaľovací kotol je napájaný pre zariadenie na napaľovanie šetrné k životnému prostrediu. podpora. V procese parenie sa delí na štyri etapy: statické zastavenie, otepľovanie, konštantná teplota a chladenie. Pri statickom zastavení by sa teplota okolia mala udržiavať pod 5 ° C a zvyšovanie teploty by sa malo kontrolovať v rozmedzí 15 ° C / h. Konštantná teplota: Keď teplota dosiahne 60 ° C, môže sa párenie zastaviť po 4 hodinách konštantnej teploty v pare. Chladenie: Rýchlosť chladenia integrovaného potrubia v parnom kúpeli je nižšia ako 10 ° C / h a povrchová teplota integrovanej trubice nie je väčšia ako 5 ° C, takže integrovaná rúra môže byť odstránená z naparovací kryt. Počas procesu napaľovania sú špeciálne pracovníci usporiadaní tak, aby efektívne kontrolovali nárast a pokles teploty a detailne zaznamenávali. Po prvé, po integrácii a zastavení integrovanej rúry na 2 hodiny bola pôvodne nastavená integrovaná galéria a inšpekcia nemá žiadne abnormality. Sprchový kryt a zariadenie sa presúvajú do prefabrikovanej výrobnej oblasti a integrovaná galéria s potrubím bola nastavená s parným krytom. Prísne zapečatené, skontrolujte stav tesnenia vriaceho zariadenia a vaňový kryt a ladenie parného zariadenia. Po skončení všetkých príprav, spustite parné zariadenie na zahriatie a venujte pozornosť regulácii rýchlosti ohrevu v priebehu vykurovania v rozmedzí 15 ° C / h. , Je zakázané zahrievať príliš rýchlo alebo príliš pomaly, čo ovplyvní pevnosť v tlaku a výkon integrovanej galérie. Keď teplota dosiahne 60 ° C, spustí sa konštantná teplota v pare. Po neustálej teplote počas štyroch hodín môže dôjsť k zastaveniu pary. Po ukončení konštantnej tepelnej pary sa integrovaná rúrková rúra ochladí a udržiava v parnom kanáli a rýchlosť chladenia je prísne kontrolovaná. Pri teplote 10 ° C / h teplota klesne na povrchovú teplotu integrovaného potrubia a okolitá teplota nepresahuje 5 ° C, môže sa odstrániť parný kryt a integrovaná rúra sa demoluje a premiestni do prírodného prostredia na prírodnú ochranu. (2) Po ukončení napaľovania bude plán údržby a plán údržby prírodnej ochrany dosiahnuť 50% konštrukčnej pevnosti a teplotný rozdiel medzi vnútornou a vonkajšou stranou parného krytu nesmie byť po zastavení vyšší ako 5 ° C v pare na jednu hodinu. plesne. Poradie demolácie je zhora zhora nadol. V procese demontáže by sa mal postupne odstrániť, forma sa odstráni, prefabrikovaná integrovaná trubková galéria a spodná forma sa vyberú z formy cez portálový žeriav a prepravujú sa do určeného prírodného chráneného prístrešku pre prírodné zalievanie. Je prísne zakázané používať páčidlo na zasunutie šablóny pod šablónu počas procesu demontáže. Po prirodzenej údržbe dosahuje 75% konštrukčnej pevnosti, integrovaná rúra sa odstráni z prírodnej ochrannej budovy, aby sa mohla obrátiť. (3) Plán skladania a rozmiestnenia rúry na rúry Po ukončení betónového odlievania je konštrukčná pevnosť 50% a po ponechaní pôdy na jednu hodinu, teplotný rozdiel medzi vnútorným a vonkajším priestorom parnej haly nemôže byť väčší ako 5 ° C a forma môže byť zničená. Poradie demolácie je zhora zhora nadol. Pri demontáži by sa mal postupne odstrániť postupne. Po odstránení formy sa prefabrikovaný výrobok a spodná forma vyťahujú z formy a prepravujú do určenej prírodnej chránenej oblasti na prirodzené zavlažovanie. Je prísne zakázané používať páčidlo na zasunutie šablóny pod šablónu počas procesu demontáže. Uhlové časti kontaktného popruhu alebo drôteného lana sú chránené podložkou, ktorá je počas zdvíhania ľahká a ľahká a všetky akcie smeruje špeciálna osoba. Po dosiahnutí 75% pevnosti dizajnu sa produkt prenesie do dokončenej prírodnej rezervácie. Produkt vysuňte z prepravky počas prepravy a produkt otočte. S cieľom uľahčiť skladovanie výrobku sa pôvodný výrobok výrobku otočí na spodnú stranu podlahy a výška skladovania výrobku je v dvoch vrstvách. 4, uzavreté normy pre testovanie vody


Kontrolný priebeh uzatvorenej vody

(1) Vstrekovanie vody v integrovanej galvanickej rúrke Pred integrovaním vody je integrovaný blok s potrubím uzatvorený a utesnený. Po absolvovaní inšpekcie sa voda vstrekne do integrovanej trubice. Voda sa vstrekuje z dolného konca integrovanej trubice. Po naplnení vody sa vnútorná stena integrovanej trubice a materiál rozhrania úplne absorbujú a doba namáčania nie je menšia ako je dĺžka špecifikovaná v špecifikácii. (2) Test a. Po komplexnom odvode rúr je v súlade s požiadavkami, vykoná sa test. Skúšobná hlava musí byť 2 m nad vrcholom integrovanej galérie. Ak je výška z hornej časti integrovanej galérie do inšpekčného prístavu nižšia ako 2 m, podľa inšpekcie kvality miestnej technickej kontroly a akceptácie Standard "hladina vody na skúšobnej hladine uzavretej vody na hlavu sondy, aby spĺňala požiadavky na stavbu. b. Začnite časovať, keď testovacia hlava dosiahne stanovenú úroveň, pozorujte únik integrovanej trubice do konca pozorovania. V tejto dobe by sa voda mala kontinuálne privádzať do integrovanej trubice, aby bola skúšobná hlava konštantná a doba presakovania priesaku vody nie je kratšia ako 30 minút. c. Vypočítajte namerané presakovanie vody podľa nasledujúceho vzorca: q = W / TL, kde q je nameraný prietok vody [L / (min.m)]; W - množstvo vody (L); T - doba pozorovania (min) L - dĺžka konca skúšobnej trubice (m). c. Po dokončení integrovanej galérie sa tretia inšpekčná strana a dozor na mieste určený stranou A oznámia včas, aby vykonali test uzavretých vôd integrovaného systému potrubia. Po dokončení testu musí zmluvná strana vykonať zásyp integrovanej výkopovej rúry. (3) Kontrolné body a. Integrovaná rúra musí byť kontrolovaná podľa sekcie; b. Kvalita vzhľadu integrovaného potrubia a inšpekčnej studne je kvalifikovaná a nie sú kvalifikované žiadne úniky vody a žiadny vážny priesak vody; c. Doba namáčania po naplnení vody v integrovanej rúre potrubia Čas ponorenia železobetónového potrubia nesmie byť menší ako je dĺžka špecifikovaná v špecifikácii; d. Komplexný skúšobný test uzavretých vôd sa vykoná na mieste merania skutočnej sumy a výpočtu poľa a vyplní príslušné formuláre ako skrytý záznam o prijatí. (4) Upozornenie na uzavretú vodnú skúšku Uzavretá časť uzavretého vodného úseku nie je hustá a často sa zanedbáva, pretože je v studni. Ak sa tehlová stena používa na tesnenie, mali by sa venovať nasledujúce pozornosti: Hrdlo by malo byť pred zablokovaním 0,5 Vnútorná stena potrubia v rozsahu m je očistená, sú navlhčené na použitie. Murovaná malta nesmie byť menšia ako M7,5 a má dobrú konzistenciu. Cementová malta na spájanie a omietanie nesmie byť menšia ako M15. Ak je priemer rúry veľký, vnútorná a vonkajšia strana by mala byť malá a mala by sa použiť iba vonkajšia jednostranná spojka alebo plocha. Povrch by sa mal aplikovať vo vodotesnej 5-vrstvovej konštrukcii. Ak to podmienky dovolia, môže byť pred kontrolou studní zapečatené, aby sa zabezpečila kvalita. Prednastavený odtokový otvor by mal byť skontrolovaný na vnútornom spodku rúrky na odvodnenie a testovanie. (5) Spracovanie priesaku vody v integrovanej galvanizačnej rúre Test uzavretých vôd je komplexnou prehliadkou výstavby integrovanej trubice a kvality materiálov. In the event of leakage, the leaks should be marked first and carefully treated after draining the water in the integrated pipe gallery. After the treatment, the test is repeated, and the process is repeated until the water is closed. Third, the material quality: 1, steel; the use of tensile strength is not lower than HRB400 three-stage threaded steel or hot-rolled, cold-rolled ribbed steel, steel properties should meet the requirements of GB1499.2, GB13788, GB1499.1. 2, cement; should use Portland cement, ordinary Portland cement, can also use sulfate-resistant Portland cement, fast-hardening cement. Cement performance should meet the requirements of GB175 and GB748 respectively. 3, aggregate; fine aggregate should use medium coarse sand, fineness modulus 2.3~3.3, mud content is not more than 2%; the maximum particle size of coarse aggregate should not exceed 1/3 of wall thickness of reinforced concrete box culvert, It shall not be greater than 3/4 of the net spacing of the hoop reinforcing bars, the mud content is ≤1%, the stone powder content is ≤5%, the needle-like particle content is ≤10%, and the porosity is ≤45%. 4. Admixtures and admixtures; concrete may not have harmful effects on box culverts when admixtures and admixtures are added. Should comply with the provisions of GB8076. When adding the sodium and polycarboxylate water reducing agent, the amount of addition should be determined after the test; the amount of FDN-2 superplasticizer is 0.75%~1%. The polycarboxylic acid series water reducing agent should be based on The amount of dilution of the mother agent is determined. 5. Water: Concrete mixing water should meet the requirements of JGJ63. 4. Box culvert standard: 1. Appearance quality inspection is as follows: (1) The inner and outer surfaces of the box should be dense, smooth and clean, free from cracks, honeycombs, pockmarks, pores, sinks, exposed sand, exposed stones, exposed pulp and sticky skin. , (2) The end face of the socket should be clean and free of angles. Cracks, exposed ribs, etc. are not densely realized. The groove of the adhesive strip of the socket should be smooth and smooth, the grain is clear, and there should be no sticking of floating pulp and debris. (3) The inner and outer surfaces of the top and bottom plates should be flat and free from local unevenness. (4) The sidewall pre-embedded screws should be firm, the silk path should be smooth and neatly arranged. (5) The tension hole should be smooth, the aperture is consistent, and there is no skew deviation.


2, product size deviation (1) steel frame: height ± 5mm, length ± 5mm, width ± 3mm, reinforced bar ± 5mm, steel bar diameter ± 0.1mm (2) box culvert: height ± 5mm, length ± 2mm, width ±2mm, socket depth ±1mm, socket length ±1mm, wall thickness ±1mm. (3) Box culvert parameter concrete 28d compressive strength C45/, demoulding strength requirement reaches 20Mpa, impermeability When P6 is reached, the freezing and thawing reaches F100, the external pressure crack load reaches 85kn/m, and the failure load reaches 120kn/m. First, the venue settings

19e0885965a9620c7b4ea459ffc0934f.jpg

Prefabricated site

1. The site is selected according to the actual situation of the project. The site adopts closed management to set up import and export, and the construction access road is reserved in the site planning area, and various signs are hanged at the import and export according to regulations. 2. The layout of the prefabrication site shall be in strict accordance with the requirements of the standard factory, meet the requirements of occupational health and safety and environmental management system and HSE operation instructions, and set up various safety environment protection facilities. It shall be fully equipped to meet the requirements of safe and civilized production, sewage discharge and garbage disposal. Strictly in accordance with the relevant provisions of local government departments. 3. Clean the prefabricated site, leveling, vibrating and compacting, laying a 20cm thick cement stabilized macadam base, smoothing and vibrating and compacting. The main road of the plant will pour 15cm thick C20 commercial concrete on the cement stabilized macadam base. , installation area, prefabrication, production area, integrated pipe gallery natural conservation placement area pouring 10cmC20 commercial concrete. In the gantry crane rail erection position, the excavation depth is 60cm, and the concrete is poured and the track is laid. We must also do these three things: (1) The site needs to be cleaned and leveled, including prefabricated sites, connecting construction work belts and existing transportation roads, and passages in prefabricated sites. (2) In the prefabricated site, the stones, weeds, trees, structures, etc. that affect the passage or construction work of the construction machinery should be cleaned up, the ditch and the ridge should be leveled, and the low-lying areas with accumulated water should be drained and filled, if necessary, changed. Fill in, fully guarantee the flatness of the ground and the load-bearing and compressive capacity. (3) Pre-fabrication site cleaning and leveling shall be carried out to save land acquisition or land occupation, no traffic obstruction, no damage to buildings, facilities, monuments, etc., to prevent environmental pollution and soil erosion. 4. Prefabrication of the steel bar processing and installation area, integrated pipe gallery prefabrication production steaming area, integrated pipe gallery natural conservation shed, integrated pipe gallery storage area and other functional areas. The office area and living area are set according to the actual situation, and the prefabricated field entrance and exit is set up as a guard room. Second, the production process


Production process flow chart

1. Reinforcement engineering construction materials entering the site, sampling inspection, steel processing, steel bar binding, installation. (1) Reinforcement approach inspection a. Rebar is hot-rolled HPB300 grade steel and hot-rolled HRB400 grade steel bar. The standard strength of steel bar meets the requirements of 4.2.2 of GB50010-2010. The ribbed steel bar complies with the steel for reinforced concrete: Part II: Hot-rolled ribbed steel bars (GB1499.2-2007); light-round steel bars meet the requirements of steel for reinforced concrete: Part I: Hot-rolled ribbed steel bars (GB1499.1-2008). The steel plate is made of Q235-B steel, the welding electrode HPB300 grade steel is welded with E43 type electrode, and the HRB400 grade steel is welded with E55 type electrode. b. Before the steel enters the site, check the variety, grade, specification, quantity and material list in strict accordance with the requirements, whether the product quality certificate, the factory inspection report and the re-inspection report are complete and valid. The mechanical properties test must be in accordance with the relevant standards. c. Before the steel enters the field and before use, check the appearance quality of the steel bar, whether it is straight, no damage, no slag inclusion on the surface, heavy skin, crack, oil stain, granular or flake old rust, uniform color, view the diameter of the steel bar Meet the requirements, so as not to affect the strength of the steel and anchoring performance. Steel plates, welding rods, etc. are inspected with the steel bar inspection items before entering the site. (2) Storage of steel bars a. The steel bars entering the site are stored in the steel bar storage area according to the variety, specification and grade. The materials are stored by the material staff and the custodians. The steel bar is required to be covered with a pad to prevent rust. b. Check whether the steel bar has the factory certificate and the factory inspection report and the re-inspection report. Check the appearance quality and the volume representative diameter. The steel bar must be inspected comprehensively for its quality index. According to the batch inspection, the diameter and weight deviation are the same as the same factory, the same furnace number, the same specification, the same production process, and the 60-ton steel bar entering the same construction site at the same time is an inspection lot, less than 60 tons. Also as a test lot, carry out witnessed sampling. Sampling of steel bars shall be carried out by the supervising engineer. Two steel bars shall be taken to take two tensile test pieces, each with a length of about 450 mm, and two cold-bent test pieces with a length of about 350 mm, placed in the test box, and then supervised for sealing or monitoring the test room. If the result of the re-examination report is unqualified, it shall be double-sampled and re-tested. The results of the re-examination report shall be qualified, and the professional supervision engineer shall sign the approval, and the batch of steel bars may be used in processing. Storage and storage of other materials shall be carried out by means of moisture insulation. (3) Rebar processing Before processing, according to the design specifications and length and quantity, combined with different processing techniques, the length of each rebar is determined by calculation to ensure accuracy. During processing, check whether there is any error or omission in the blanking table. Check the material table for each type of steel bar. After these two inspections, press the material table to release the real sample. After the trial production is qualified, it can be processed in batches. Good steel bars should be stacked neatly and orderly. The surface of the steel bar should be clean, and the grease, dirt and rust must be cleaned before use. The steel bars are straightened and mechanically straightened. The steel bars after straightening shall not have local bending, dead bends or small waves. The steel bar cutting should be based on the steel bar number, diameter, length and quantity. The length and length of the steel bar should be broken and the short material should be broken first, and the short steel head should be reduced and shortened as much as possible to save steel and reduce loss. When the steel bar is bent, stake out determines the bending point and determines the bending angle based on the rebound strength of each steel bar. Before the formal bending, the steel bars that have been bent in large quantities will be subjected to trial bending and the relevant technical data will be determined before batch bending. After the steel bar is bent, the arc forms an arc. After the bending, the size is not larger than the blanking size. The bending adjustment value should be considered. The bending diameter D of the bent steel bar and the bend of the middle part is not less than 5 times the diameter of the steel bar. The length of the steel bar should be considered comprehensively according to the size of the component, the thickness of the protective layer, and the adjustment value of the bending of the steel bar. The allowable deviation of steel bar processing shall not exceed the specification. For steel bars with insufficient finished material, the butt joint pressure welding method is used to butt the foot length and then bend. The butt welder must be trained in a special butt welding process and sampled for inspection. After the various steel bars are formed, the allowable deviation shall not exceed the specification: the full length of the force ribs shall be ±10 mm; the deviation of the length of each part of the stirrups shall be ±5 mm; the deviation of the bent ribs shall be ±20 mm of the member, large volume The concrete is ±30mm; the deviation of the steel corner is 3mm; the 6~12mm round rib is made into the stirrup, and the length of the end hook is 75~105mm according to the diameter of the main rib. The specific calculation before the blanking is determined, the processed steel bars are classified and stored, and the formed steel bars are prevented from being deformed during storage and transportation.


Braided skeleton (reinforced steel) steel formwork

Difficulties: The difficulty in making the main ribs of the rectangular top pipe is the outer rib main rib. Each ring consists of four steel bars with two arcs each forming a rectangular top pipe rebar ring. The radius of the arc is too small, the curved arc segment is short, and the precision is high. , Solution: Before the steel bars are bent, mark them at the intersection of each arc. Then, the R90 degree arc is bent by three-roll bending, and the straight line segment is not bent. After the arc is fully bent, it is placed on the standard master inspection. After the requirements are met, the moving wheel movement position mark is made on the bending machine operating platform for the next quick production. The three-roll bending machine needs to have the function of jog and reverse. (4) Steel bar welding The formed steel bar is placed on the steel bar welding work tool according to the construction drawings for welding. The welding quality is an important part to ensure the overall strength of the steel bar. In the steel bar processing factory, the steel bars are mainly cleaned by double-sided flash butt welding to clean the corner burrs and the end face rust, oil stains and oxide film before being welded, and the metal luster is exposed by grinding, and there is no oxidation phenomenon. At the same time, the end face of the steel bar should be flattened to facilitate a good combination. The fixtures on both sides should be aligned to ensure that the two steel bars are on the same axis, and the local clearance of the two steel bars is not more than 3 mm. The pressure applied during the welding should be uniform and strong, and the temperature should be controlled at 30-40 MPa depending on the diameter of the steel bar to achieve good adhesion between the two steel bars. When the steel bars of different diameters are butt welded, the deviation shall not exceed 7mm. Butt welding and spot welding are strictly in accordance with the regulations, and the welding personnel are certified to work. After the welding is completed, the joint will be changed from white to black to release the clamp, and the steel bar will be taken out smoothly to avoid bending. After the welding of the steel bars is completed, the appearance inspection of the welded joints shall be carried out in time, and the joints that fail the visual inspection shall be re-welded. All welding operators must ensure that all types of welding machines are in good working condition, master the main performance and parameters of various welding machines in time, and select the best parameters for actual operation according to the conditions of the base metal and weather to ensure the welding quality. , (5) Reinforced steel cages should be re-calibrated before specification, size, shape, quantity, positioning tooling, etc., and comprehensive inspection should be carried out according to the design drawings and ingredient list. The design, ingredient list and physical object can be matched. Security. Before the system is installed, the reinforcement is arranged on the positioning tooling platform according to the design data. At the same time, according to the location, the setting of the standing reinforcement is determined to ensure that the steel bars after the installation meet the requirements. In the process of security, the steel bars are mainly made by wire binding and spot welding. The holes are made of 20~22# wire. The method of binding and binding is in accordance with the specifications and regulations. Spot welding is mainly used for forming steel bars and standing bars. The fixing, the spot welding should be firm, the points should be evenly distributed, and the force ribs should not be seriously damaged. The lashing joint of the steel bar shall meet the following requirements: a. The end of the lap length shall be not less than 10 times the diameter of the steel bar at the bend of the steel bar, and the joint shall not be located at the maximum bending moment of the component. b. In the tension zone, the end of the I-grade steel lashing joint shall be made into a hook. In the same section, the cross-sectional area of the joint of the tension zone shall be less than 50% of the total area of the force-receiving joint, and the lashing joint shall not be more than 50%. Not more than 25%, at the same time, the lashing joints must not exceed 50% in the compression zone. c. Reinforced joints, tied with wire at the center and at both ends. d. The joint positions of the stressed ribs are staggered from each other. The lap length of the tensioned steel reinforced joints should meet the structural design requirements. The welded steel joints and mechanical joints should be placed at the minimum bending moment and staggered. e. When the diameter of the stressed steel bar is ≥25mm, it is not advisable to use a non-welded lashing joint. f. The thickness of the concrete protective layer of the stressed steel bar should meet the structural design requirements. In order to ensure the correct position of the steel bar, it is tied and installed according to the design requirements. g. In the reinforcement cage binding process, one ΦPVC pipe is pre-buried on the four sides of the joint, Φ14mm, the length of the PVC pipe is determined according to the wall thickness of the mouth of the joint, and the pre-embedded PVC pipe is used as the inspection hole and the injection hole. The lifting holes are installed at 500mm above and below the central axis of the left and right sides of the integrated pipe gallery. Two Φ125*10mm*220mm steel pipes are welded to the steel frame, and Φ140*4 steel plate is used for sealing. The Φ125*10mm*180mm steel pipe is installed before lifting. Φ110mm*350mm iron pin is used as the integrated pipe hanger ear to meet the hoisting construction of the integrated pipe gallery. Reinforced steel works are concealed projects. Before pouring concrete, the steel bars and embedded parts should be inspected and accepted, and the hidden engineering records should be made. After the on-site supervision engineers agree, the next process can be carried out.

92074dd65836ec55b1746a4e64e64b32.jpg

Steel mold assembly

The most efficient method for the assembly process should be: first support the inner mold, the steel collar connection ribs should be welded first and then placed in the bottom mold, and the lining steel ring connecting ribs of the socket should be welded after the steel frame is put into the mold, and the steel bars are welded. After the skeleton is put into the mold, the grouting hole, the grouting hole and the pre-embedded steel plate are welded. After the welding, the outer mold is assembled. In order to prevent the position of the lifting hole from being inaccurate, the lifting hole is fixed on the outer mold, and the outer mold is assembled and then the welding socket is pre-prepared. Buried steel ring. (6) Reinforced protective layer The protective layer of concrete is made of concrete block, the thickness is equal to the thickness of the designed protective layer, the block size is 3cm×3cm, the pad number is more than C25 mortar strength, and the curing is strengthened during production to achieve design strength. 85% of the above can be used. When used in the vertical structure, the 20# binding line can be buried in the block, and the block is tied to the steel bar with the wire. The bottom layer of the bottom plate and the wall reinforcement layer are placed one square meter per square meter, and the plum blossoms are arranged. The spacing of the pads should be properly encrypted. Reasonably arrange the blocks, and tie them tightly on the stressed steel bars, instead of being placed on the non-stressed tendons, the fixing should be firm to prevent displacement and slippage during the pouring process; whether the blocks are fully inspected before concrete pouring Missing or damaged. 2. Concrete pouring (1) Concrete material Concrete transportation is transported to the prefabricated site by concrete tanker, and pumped into the warehouse by concrete pump truck. The slump of concrete is generally controlled between 140 and 180 mm (the specific value depends on the temperature of the day). 4 concrete vibrating rods with a vibrating radius of 20-25cm, so the spacing between each rod is 40cm. Each rod depth is within 5cm below the previous vibrating surface, and the vibrating time per rod is 2-3 minutes. (2) Mixing ratio design and test a. Mixing ratio design To meet the requirements of concrete design strength, frost resistance, impermeability, sand aggregate expansion rate and construction workability, the concrete construction mix ratio optimization test At the same time, it meets the requirements of construction water-cement ratio and slump, and is reviewed and approved by the supervision engineer. The mix ratio of concrete should ensure that the concrete obtained can meet the specific pouring conditions, and the water consumption in the concrete mix ratio is as small as possible. b. Concrete mix ratio test concrete mix ratio test plan, including concrete mix ratio test and concrete performance test of different strength grades, blending ratio test 14d ahead of the various mix ratio test ingredients and mixing, molding and maintenance, etc. The mix ratio test plan is reported to the supervision engineer. c. Construction mix ratio control According to the mix ratio test and the batch list approved by the supervision engineer, the concrete mix ratio is controlled, and the total water consumption is adjusted according to the water content of the aggregate. Concrete slump is determined by the nature of the structural part, the rate of reinforcement, the concrete transport and casting method, and the climatic conditions, and uses a small slump as much as possible. Concrete slump meets the requirements of SL677-2014. (3) Concrete sampling test During the concrete pouring process, the contractor shall carry out concrete sampling test at the discharge opening and pouring site according to the provisions of SL352-2006 and the instructions of the supervisor, and submit the following materials to the supervisor: a. And the quality certificate of its integrated pipe gallery; b. The composition, mixing and dimensions of the test piece; c. Description of the preparation and maintenance of the test piece; d. Test results and description; e. Concrete of various ages Test data such as bulk density, compressive strength, tensile strength, ultimate tensile value, elastic modulus, Poisson's ratio, slump and initial setting and final setting time. (4) Concrete pouring a. The mix ratio of commercial concrete should meet the requirements of DL/T5330-2005 "Design Specification for Hydraulic Concrete Mixing Ratio", and use cement and water reducing agent with relatively early initial setting time and early strength increase after final setting. Various additives such as air entraining agent and early strength agent should consider the long distance of concrete transportation, increase the early strength of concrete, reduce the time of demoulding, shorten the construction period, and especially solve the slow growth of concrete strength during winter construction. The problem with the site concrete slump is to be controlled at 140-180mm. b. After the mold and steel bars have been installed and qualified by the technicians for quality inspection and supervision, and confirmed, the integrated pipe gallery can be poured. The height of the hole is 2m or more above the ground, and the drop is 2m or less. The soft string barrel is set at the mouth to ensure that the concrete has a falling height of less than 2m. c. The concrete pipe tunnel concrete shall adopt the symmetric casting method to consider that the height of the edge should not exceed 40cm, and the construction by continuous casting method should not be intermittent. d. Concrete is poured in layers, in a certain direction, and with a certain thickness. The concrete is horizontally layered and the layer thickness is 30-40 cm. e. Vibrating uses a plug-in vibrating rod, the moving distance does not exceed 1.5 times the radius of action of the vibrating bar, and maintains a distance of 5 to 10 cm from the side mold. Insert the lower layer of concrete 5 to 10 cm when vibrating, and slowly propose the vibrating bar after each vibration. Avoid vibrating the formwork, steel bars, etc. during vibration; for each vibration part, it must be oscillated until the concrete is compacted, that is, the concrete stops sinking, no bubbles appear, and the surface is flat and muddy. During the pouring process, each work type should be arranged to check the changes of steel bars, brackets and stencils, and the situation should be dealt with in time. 3, box culvert maintenance and demoulding


Box culvert prefabricated

(1) After the concrete is poured, after the concrete is initially set, the integrated pipe gallery is steamed at a high temperature. The steaming adopts a customized steaming cover, and the integrated pipe gallery mold is covered with a steaming cover, and the bottom of the steaming cover is sealed to prevent steam from being discharged during the steaming process. The steaming boiler is steamed for the environmentally friendly steaming facility. support. In the process of steaming, it is divided into four stages: static stop, warming, constant temperature and cooling. During the static stop, the ambient temperature should be kept below 5 °C, and the temperature rise should be controlled within 15 °C/h. Constant temperature: When the temperature reaches 60 °C, the steaming can be stopped after four hours of constant temperature steaming. Cooling: The cooling rate of the integrated pipe gallery in the steaming shed is less than 10 °C / h, and the surface temperature of the integrated pipe gallery is not more than 5 °C, so that the integrated pipe gallery can be removed from the steaming cover. During the steaming process, special personnel are arranged to effectively control the temperature rise and fall and record in detail. Firstly, after the integrated pipe gallery has been poured and stopped for 2 hours, the integrated pipe gallery has been initially set and the inspection has no abnormality. The steaming cover and equipment are moved to the prefabricated production area, and the integrated pipe gallery has been set up with the steaming cover. Strictly sealed, check the sealing condition of steaming equipment and steaming cover and debug the steaming equipment. After all the preparations are in place, start the steaming equipment to heat up, and pay attention to control the heating rate within 15 °C/h during the heating process. , It is forbidden to heat up too fast or too slow, which will affect the compressive strength and performance of the integrated pipe gallery. When the temperature reaches 60 °C, the constant temperature steaming is started. After the constant temperature steaming for four hours, the steaming can be stopped. After the constant temperature steaming is finished, the integrated pipe gallery is cooled and maintained in the steaming shed, and the cooling rate is strictly controlled. Within 10 °C / h, the temperature drops to the surface temperature of the integrated pipe gallery and the ambient temperature does not exceed 5 °C, the steaming cover can be removed, and the integrated pipe gallery is demolished and moved to a natural conservation shed for natural conservation. (2) After the steaming is completed, the pipe gallery demoulding and natural conservation shed maintenance plan will reach 50% of the design strength and the temperature difference between the inside and outside of the steaming cover can not be more than 5 °C after stopping the steaming for one hour. mold. The order of demolding is from the inside out, from top to bottom. In the process of dismantling, it should be removed step by step in order, the mold is removed, the prefabricated integrated pipe gallery and the bottom mold are removed from the mold by the gantry crane, and transported to the designated natural conservation shed for natural watering. It is strictly forbidden to use the crowbar to hit the stencil under the template during the demoulding process. After the natural maintenance reaches 75% of the design strength, the integrated pipe gallery will be removed from the natural conservation shed for reversal. (3) Folding and placing plan of the pipe gallery After the concrete pouring is completed, the design strength is 50% and after the steaming is stopped for one hour, the temperature difference between the inside and outside of the steaming shed can not be greater than 5 °C, and the mold can be demolished. The order of demolding is from the inside out, from top to bottom. In the process of dismantling, it should be removed step by step in sequence. After the mold is removed, the prefabricated product and the bottom mold are lifted out of the mold and transported to the designated natural conservation area for natural watering. It is strictly forbidden to use the crowbar to hit the stencil under the template during the demoulding process. The angular parts of the sling or wire rope contact are protected by a pad, which is light and light during the lifting process, and all actions are directed by a special person. After the product strength reaches 75% of the design strength, the product is transferred to the finished natural conservation area. Move the product out of the tray during transport and flip the product. In order to facilitate the storage of the product, the original product of the product is turned over to the bottom of the floor, and the product storage height is two layers. 4, closed water testing standards


Closed water inspection flow chart

(1) Water injection in the integrated pipe gallery Before the water injection, the integrated pipe gallery block is sealed and sealed. After passing the inspection, water is injected into the integrated pipe gallery. The water is injected from the lower end of the integrated pipe gallery. After the water is filled, the inner wall of the integrated pipe gallery and the interface material are fully absorbed, and the soaking time is not less than the length specified in the specification. (2) Test a. After the comprehensive pipe shed is in compliance with the requirements, the test shall be carried out. The test head shall be 2 m above the top of the integrated pipe gallery. If the height from the top of the upstream integrated pipe gallery to the inspection port is less than 2 m, according to the municipal engineering quality inspection and acceptance Standard “closed water test water level to the wellhead to meet construction requirements. b. Start timing when the test head reaches the specified level, observe the leakage of the integrated pipe gallery until the end of the observation. At this time, the water should be continuously supplied to the integrated pipe gallery to keep the test head constant, and the seepage time of the water seepage is not less than 30 minutes. c. Calculate the measured water seepage according to the following formula: q=W/TL where q is the measured water seepage [L/(min.m)]; W——the amount of water (L); T——observation time (min) L - length of the test tube end (m). c. After the completion of the integrated pipe gallery, the third inspection party and the on-site supervision designated by Party A shall be notified in time to carry out the closed water test of the integrated pipe gallery system. After the test is completed, the earthwork construction party shall carry out the backfilling of the integrated pipe gallery trench. (3) Checkpoints a. The integrated pipe gallery must be inspected section by section; b. The appearance quality of the integrated pipe gallery and inspection well has been qualified, and no water leakage and no serious water seepage are qualified; c. Soaking time after filling the water in the integrated pipe gallery The immersion time of the reinforced concrete pipe shall not be less than the length specified in the specification; d. The comprehensive pipe gallery closed water test shall be carried out on site to measure the actual amount and the field calculation, and fill in the relevant forms as a concealed acceptance record. (4) Notice of closed water test The closed section of the closed water section is not dense, and it is often neglected because it is in the well. If the brick wall is used for sealing, the following points should be paid attention to: The nozzle should be 0.5 before the blockage The inner wall of the pipe in the range of m is cleaned, the cement puree is painted, and the bricks used are wetted for use. The masonry mortar should be no less than M7.5 and have a good consistency. The cement mortar for jointing and plastering shall be not less than M15. When the diameter of the pipe is large, the inner and outer sides should be small and only the outer one-side joint or the surface should be used. The surface should be applied in a waterproof 5-layer construction method. When conditions permit, it can be sealed before the inspection of the wells to ensure quality. The preset drain hole should be inspected at the inner bottom of the tube for draining and testing. (5) Treatment of water seepage in integrated pipe gallery The closed water test is a comprehensive inspection of the construction of integrated pipe gallery and the quality of materials. In the event of leakage, the leaks should be marked first and carefully treated after draining the water in the integrated pipe gallery. After the treatment, the test is repeated, and the process is repeated until the water is closed. Third, the material quality: 1, steel; the use of tensile strength is not lower than HRB400 three-stage threaded steel or hot-rolled, cold-rolled ribbed steel, steel properties should meet the requirements of GB1499.2, GB13788, GB1499.1. 2, cement; should use Portland cement, ordinary Portland cement, can also use sulfate-resistant Portland cement, fast-hardening cement. Cement performance should meet the requirements of GB175 and GB748 respectively. 3, aggregate; fine aggregate should use medium coarse sand, fineness modulus 2.3~3.3, mud content is not more than 2%; the maximum particle size of coarse aggregate should not exceed 1/3 of wall thickness of reinforced concrete box culvert, It shall not be greater than 3/4 of the net spacing of the hoop reinforcing bars, the mud content is ≤1%, the stone powder content is ≤5%, the needle-like particle content is ≤10%, and the porosity is ≤45%. 4. Admixtures and admixtures; concrete may not have harmful effects on box culverts when admixtures and admixtures are added. Should comply with the provisions of GB8076. When adding the sodium and polycarboxylate water reducing agent, the amount of addition should be determined after the test; the amount of FDN-2 superplasticizer is 0.75%~1%. The polycarboxylic acid series water reducing agent should be based on The amount of dilution of the mother agent is determined. 5. Water: Concrete mixing water should meet the requirements of JGJ63. 4. Box culvert standard: 1. Appearance quality inspection is as follows: (1) The inner and outer surfaces of the box should be dense, smooth and clean, free from cracks, honeycombs, pockmarks, pores, sinks, exposed sand, exposed stones, exposed pulp and sticky skin. , (2) The end face of the socket should be clean and free of angles. Cracks, exposed ribs, etc. are not densely realized. The groove of the adhesive strip of the socket should be smooth and smooth, the grain is clear, and there should be no sticking of floating pulp and debris. (3) The inner and outer surfaces of the top and bottom plates should be flat and free from local unevenness. (4) The sidewall pre-embedded screws should be firm, the silk path should be smooth and neatly arranged. (5) The tension hole should be smooth, the aperture is consistent, and there is no skew deviation.

2, product size deviation (1) steel frame: height ± 5mm, length ± 5mm, width ± 3mm, reinforced bar ± 5mm, steel bar diameter ± 0.1mm (2) box culvert: height ± 5mm, length ± 2mm, width ±2mm, socket depth ±1mm, socket length ±1mm, wall thickness ±1mm. (3) Box culvert parameter concrete 28d compressive strength C45/, demoulding strength requirement reaches 20Mpa, impermeability When P6 is reached, the freezing and thawing reaches F100, the external pressure crack load reaches 85kn/m, and the failure load reaches 120kn/m.


Zaslať požiadavku